Kipatikana Bidhaa Maarufu
HC-HS 2-D7-EBUS
HC-HS 2-D7-EBUS 1586264 PHOENIX CONTACT Contact insert
$35.46USD
326 kwenye hisa
Vipimo Muhimu
:Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Aina:D7
Majaribio:DIN VDE 0627/86
Upana:21 mm
Taarifa za Msambazaji
Bidhaa: 0
Kwa kawaida husafirisha ndani ya siku 2-3 za kazi
Ubora Umeheshimiwa
Usafirishaji wa haraka
Msaada wa Kiufundi
Speci ya Kiufundi
| Kipengele | Thamani |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| Aina | D7 |
| Majaribio | DIN VDE 0627/86 |
| Upana | 21 mm |
| Urefu | 21 mm |
| Mfululizo | HC-HS |
| Jumla | for HC-D7 housing, axial connection 2.0 mm, Allen key |
| Maombi | Power |
| Aina ya bidhaa | Contact insert with a fixed no. of positions |
| Dokezo la mkutano | To ensure correct use, installation in housing with IP54 protection or better is required |
| Imekadiriwa mkondo | 40 A |
| Marekebisho ya makala | 04 |
| Kipenyo cha mguso | 4 mm |
| Nyenzo ya mawasiliano | Copper alloy |
| Soketi ya hexagonal | SW2,0 |
| Nambari za mawasiliano | 1 - 2 |
| Kukaza torque | 0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing) |
| Wasifu wa muunganisho | 2+PE |
| Kiwango cha uchafuzi wa mazingira | 3 |
| Mchoro wa vipimo | |
| Idadi ya nafasi | 2 |
| Volti ya kuongezeka iliyokadiriwa | 6 kV |
| Kategoria ya volteji nyingi | III |
| Teknolojia ya muunganisho | Axial screw connection |
| Aina ya nyenzo za mguso | turned |
| Idadi ya mawasiliano ya umeme | 2 |
| Volti iliyokadiriwa (III/3) | 400 V |
| Sehemu ya msalaba ya kondakta | 4 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used) |
| Nyenzo za mawasiliano | PC |
| Nyenzo ya uso wa mguso | Ag |
| Mizunguko ya kuingiza/kutoa | ≥ 500 |
| Sehemu ya muunganisho AWG | 10 ... 8 |
| Halijoto ya mazingira (uendeshaji) | -40 °C ... 125 °C (including heating up of contacts) |
| Muunganisho katika acc. na kiwango cha kawaida | IEC / EN |
| Kanuni za ujenzi na upimaji | DIN VDE 0627/86 |
| Ukadiriaji wa kuwaka kulingana na UL 94 | V0 |
| Urefu wa kukatwa kwa waya mmoja mmoja | 8 mm +1 mm |
Maelezo ya Bidhaa
Contact insert, number of poles: 2+PE, size: D7, power contacts: 2, Female, Axial screw connection, 400 V, 40 A, 4 mm² ... 10 mm², Application: Power
Vipengele Muhimu
- Ubora wa kiwango cha viwanda
- Inaendana na RoHS
- Imethibitishwa CE
- Dhamana ya mwaka 1
Nyaraka za Bidhaa
Jalada la data
Speci za kiufundi na data ya utendaji
Mwongozo wa Mtumiaji
Mwongozo wa usakinishaji na uendeshaji
